EverSync SP-10: Go Wireless With the Mic or Pickup You Already Own

You’ve already done the hard part. You found the clip-on mic that gets your horn right, or you tried pickup after pickup until one finally meet your expectation. The only thing left to fix is the cable. It pins you to one spot, it gets under the audience’s feet, and it stops you from stepping out front to interact with your audiences.

Going wireless usually means picking between a plug-in wireless guitar system and an all-in-one rig with its own mic built in. Either way, you give up part of a setup you already like. The EverSync SP-10 skips that trade. Plug in the mic or pickup you already own, and it goes wireless.

A spec sheet only tells you so much, so we’ll let the gigs do the talking. Below, you’ll hear from two players who took the SP-10 out to work: Emily McVicker, who played it on acoustic guitar for Guitar World, and Jamie Anderson of Get Your Sax Together, who put it on a concert stage.

Disclosure: the videos quoted in this article were made as paid partnerships with Cloudvocal or by Cloudvocal retail partners. The quotes are the reviewers’ own words.

Meet the SP-10: A Bodypack and a Pedal

The SP-10 is a two-piece wireless system:

  • The transmitter is a bodypack that clips onto you or your instrument. Your mic or pickup plugs in here.
  • The receiver is a stompbox that sits at your feet and feeds the mixer, PA, or amp. Gain, EQ, reverb, and boost are all on board.
EverSync SP-10 bodypack transmitter and pedal receiver

You get two outputs on the receiver: balanced XLR for a straight run to the mixer or stage box, and 1/4″ TS for an amp or the rest of your pedalboard. Or, as Jamie puts it:

It’s a wireless transmitter and stompbox-style receiver, so you can run around on stage with your instrument like an absolute rock legend.

Jamie Anderson, Get Your Sax Together

Bring Your Own Mic or Pickup

Most compact wireless rigs are built for one job. Plug-in guitar systems handle pickups. Very few will run a standalone clip-on mic, and fewer still do both. The SP-10 does both.

Clip-On Mics

The transmitter supplies bias voltage for pre-polarized condenser capsules, which covers a lot of the clip-on instrument mics out there. All you need is the right adapter cable. Here’s Jamie again:

You can use a clip mic, either the Cloudvocal SonoFlex like I’m using or most other standalone clip mics like the DPA 4099, for example. You just need the right lead.

Jamie Anderson, Get Your Sax Together
Clip-on saxophone microphone connected to the EverSync SP-10 transmitter
image captured from
The Truth About the CloudVocal Eversync SP-10 Wireless Stomp Pedal

Running a DPA 4099, Neumann MCM, Shure Beta 98, AMT, or AKG C519? Our guide to taking those mics wireless with the SP-10 lists the exact cable for each one.

Pickups

Got a pickup in your guitar or ukulele? Use the 1/4″ TS to 3.5mm cable that comes in the box. It’s wired to tell the transmitter that an instrument signal is coming in, not a mic signal, so a hot pickup won’t overload the input. That’s also why you should stick with the supplied cable. A third-party cable wired differently can leave you with distortion, or no signal at all.

Acoustic guitar pickup connected to the EverSync SP-10 transmitter with the included 1/4" to 1/8" cable
image captured from
Emily McVicker: My three acoustic gigs with the EverSync SP-10 Wireless pedal

That’s how Emily McVicker ran it for Guitar World, straight from the pickup in her Fender acoustic. She described it as a wireless “made for acoustic guitars.” Still weighing up a pickup against a mic? Our guide to acoustic guitar pickups and microphones lays out the trade-offs.

What It Won’t Run

Two things to check before you order:

  • Mics that need 48V phantom power. The transmitter doesn’t supply 48V. If your mic’s spec sheet calls for it, the mic may not work properly.
  • Mics from all-in-one wireless systems. In Jamie’s words, “you can’t use the mic from an all-in-one wireless system.” You need a standalone clip mic, the kind that normally plugs into a separate transmitter.

DI, EQ, Reverb, and Boost in One Pedal

If you’ve used a plug-in wireless system, you know the catch. The cable’s gone, but the moment you want EQ or a touch of reverb, you’re back to adding a preamp or another pedal. Same amount of gear in the bag, same hunt for a power outlet at the venue.

Emily took the SP-10 to three very different rooms and didn’t need anything else:

I played three gigs with the SP-10. I played a family-friendly pub, I played a total dive bar, and I played a wedding cocktail hour. […] The SP-10 made my guitar sound really nice, and it was a very simple, streamlined setup for an acoustic gig like that. I was able to add basic EQ and reverb.

Emily McVicker, Guitar World

Here’s what you get:

  • Gain and pad: up to +30dB of gain for quiet sources, plus a pad for loud ones.
  • EQ: flat, low cut, high cut, or both. On a piezo pickup, the high cut takes the harsh edge off hard strumming.
  • Reverb: small room, small hall, or large hall. You set the amount from a dial on the transmitter, so you can tweak it between songs without bending down.
  • Boost: +6dB out of the box, adjustable up to +9dB, and it sits on the footswitch for when your solo comes around.
  • Mute: from the footswitch or the transmitter. Handy when you’re switching instruments.
  • Balanced XLR out: the DI is built in, so it’s one cable from your feet to the mixer.
EverSync SP-10 pedal receiver with the EQ setting shown on its display

A word of warning on that reverb dial from Jamie: it’s “very cool,” but “you have to be careful you don’t adjust it by accident.” Give it a quick look before you start your set.

Not sure whether you need a DI, or what goes wrong without one? Start with Do I Need a DI Box? And if you play sax and want to see the boost and EQ at work mid-gig, our write-up of the SAX review covers each control.

Power It From a Power Bank

The receiver runs on a standard 9V DC pedal supply or on USB-C, and USB-C means a power bank will do the job. A market stall, a workshop, a venue with no outlet anywhere near the stage: you’re covered. It makes travel easier too, with no plug adapters or mains voltage to think about.

EverSync SP-10 pedal receiver powered by a USB-C power bank

Emily made the same connection for buskers:

The pedal can be powered with a regular 9-volt, but you can also use a USB-C. So that also means if you’re busking, you can do it completely wireless if you had some kind of a power brick to plug the USB-C.

Emily McVicker, Guitar World

Will It Drop Out? The Numbers and a Concert Stage Test

Dropouts and latency are the two things that put players off wireless. The SP-10 runs on Cloudvocal’s own 2.4GHz protocol. Here’s how it measures up in our testing and at real shows:

SpecWhat to expect
Latency9ms in standard mode, 6.6ms in low-latency mode
RangeUp to 30m (about 100ft), measured in standard mode with clear line of sight. Real-world range depends on the venue.
Transmitter batteryAt least 10 hours on a full charge
Systems at onceUp to 8, a setup that has been used on stage at a live concert

Jamie plays horns with Wet Wet Wet in the UK, and he tried the SP-10 on a concert stage with the show’s sound engineer. He plugged the receiver straight into the stage box and went for a walk:

In this particular hall I couldn’t get far enough away for it to stop working, which is quite impressive.

Jamie Anderson, Get Your Sax Together

Then he asked Rick, the engineer, how it stacked up against the system he normally works with:

It sounds very similar to our high-end wireless system that we use. […] I could leave the EQ the same. Came in a little bit hotter, so I had to adjust the levels, but apart from that, sounds pretty good.

Rick, concert sound engineer, in the Get Your Sax Together review

There’s one more upside you won’t find on a spec sheet. Emily soundchecked her wedding gig without a cable, “because that way I could walk around and hear for myself how the guitar was sounding.” With no engineer out front, walking the room yourself is the only way to hear what the audience hears.

One honest caveat: 2.4GHz is a shared band, and a packed room behaves differently from an empty one. Always test in the venue before a gig that matters. To learn how 2.4GHz systems work and how to keep dropouts at bay, read how wireless microphones work.

SP-10 vs. Other Ways to Go Wireless

Plug-in wireless guitar systemTraditional bodypack systemEverSync SP-10
What it takesUsually pickups onlyUsually microphonesMicrophones and pickups
Tone shapingNeeds a separate preamp or pedalDone at the mixer, by the engineerGain, EQ, reverb, and boost built in
Receiver sizeSmallUsually largerPedal-sized
Receiver powerUsually an internal batteryUsually a mains adapterUSB-C (a power bank works) or 9V DC

Next to a plug-in system, you gain flexibility and control over your tone. Next to a traditional bodypack system, you get a smaller receiver, more ways to route your signal, and easier power.

Is the SP-10 Right for You?

It’s a good fit if you:

  • Already have a mic or pickup you love and want to keep that sound
  • Play pubs, weddings, markets, small festivals, or the street, and want to carry less without giving up your tone
  • Travel to gigs and can’t count on an outlet or the right voltage
  • Play in a group where several people need wireless and pairing has to be fast

Look elsewhere if you:

  • Use a mic that needs 48V phantom power
  • Don’t own a mic yet and want the mic and transmitter in one unit. ISOLO is the closer match, and our SP-10 vs. ISOLO comparison explains the difference

EverSync SP-10

Your mic. Now wireless.

Full specs, what’s in the box, and the adapter cable for each mic are on the product page. Not sure your mic or pickup will work? Ask us before you order.

See the EverSync SP-10 →

Wireless is one link in your live sound chain. For the rest, from the instrument itself to mic choice and tone shaping, head to Saxophone Live Sound: The Complete Guide.

Soundstage noise maker
Soundstage noise maker
Articles: 57

Leave a Reply

Your email address will not be published. Required fields are marked *